Mounts · Made in Michigan
Shotgun Round Holder
Faster Reloads & One-More-Shot Confidence with a Shotgun Round Holder. Universal shotgun round holders keep a spare shell exactly where you want it for quick, reliable reloads.
- Free shipping $20+
- Lifetime warranty
- Made in Michigan
- Free returns
The lineup
The Guide
Choose Your Gauge: 12, 20, or .410
Match the holder to your shotgun gauge for a secure, rattle-free grip and predictable reloads. A gauge-specific channel keeps the shell snug so it stays put through recoil and movement.
- Gauge-specific fit improves retention and access
- Reduces fumbles during hunting, drills, or competition
Mounting & Surface Prep for 3M VHB Adhesive
For the strongest bond, clean any flat surface with isopropyl alcohol and let it dry before applying. Press firmly and allow the adhesive to set for best long-term hold.
- Clean, flat areas deliver the best adhesion
- No tools or gunsmithing—peel, stick, press
Placement Strategy: Speed, Access, and Balance
Place the holder where your support hand naturally reaches without breaking your mount or sight picture. Keep it low-profile and out of snag zones on slings or gear.
- Position for a straight, eyes-up grab
- Avoid sling contact and clothing snags
Materials & Durability You Can Trust
Nylon 12 resists impact and weather, while 3M VHB stands up to recoil, temperature swings, and moisture. The low-profile form follows the receiver or stock to minimize snags.
- Weather-resistant Nylon 12 + 3M VHB
- Slim design adds negligible weight
Field manual
Will these shotgun round holders fit my specific model?
Yes—each holder mounts to any clean, flat surface on most shotguns and is gauge-specific for 12 gauge, 20 gauge, or .410 shells. The industrial 3M VHB adhesive forms a strong, permanent bond to compatible areas on the receiver or stock, delivering a universal, brand-agnostic fit for common platforms. Choose the gauge that matches your shotgun for the most secure retention and consistent reloads."
How strong is the 3M VHB adhesive for recoil and weather?
3M VHB is an industrial-grade adhesive designed for high-stress applications, so it handles recoil, vibration, and temperature swings with ease. Once applied correctly to a clean, dry, flat surface and pressed firmly, it resists rain, mud, and cold for dependable, long-term use. Many shooters prefer it because it eliminates drilling or hardware while maintaining excellent durability in field conditions."
Can I remove or reposition the holder later?
The adhesive is intended for a permanent bond, but it can be removed with care. Apply gentle heat (a household hair dryer works) to soften the tape, then work a plastic scraper under the base to lift it without gouging the surface. If you plan to remount, use new 3M VHB tape and repeat the surface-prep steps to restore full holding strength."
Does the holder add noticeable weight or bulk to my setup?
No—the low-profile design adds virtually no bulk and weighs roughly a quarter of an ounce, so handling remains quick and natural. The slim footprint hugs the gun to reduce snags on slings, clothing, and brush, preserving your balance and mount. It’s a ‘set-and-forget’ upgrade that pays off every time you need one more shell."
What materials are used, and how do they hold up over time?
The body is Nylon 12, a tough engineering plastic that resists impact, abrasion, and moisture, paired with 3M VHB adhesive that maintains grip through temperature and weather changes. This combination is ideal for shotguns that see hard use at the range or in the field. With proper prep and placement, you can expect season-after-season reliability."
Where should I place the holder for the fastest reloads?
Mount it where your support hand naturally falls so you can grab the shell by feel without shifting your eyes off the target. Many shooters prefer a flat section along the receiver or stock where the profile stays low and snag-free. Test an unloaded draw motion to confirm that your index is repeatable before final placement."